This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
chara:fringe_offsets [2023/04/20 18:03] gail_stargazer |
chara:fringe_offsets [2023/06/29 21:17] gail_stargazer |
||
---|---|---|---|
Line 2: | Line 2: | ||
The fringe offsets on any given night will depend on the POP configuration and the daily alignment. The table below gives a range of values where the fringes have been found for each cart on multiple nights across different POP configurations. The ranges should at least provide a guide for how far one might need to look to find fringes. The relative offsets between any pair of telescopes can be calculated from the differences between the ranges. | The fringe offsets on any given night will depend on the POP configuration and the daily alignment. The table below gives a range of values where the fringes have been found for each cart on multiple nights across different POP configurations. The ranges should at least provide a guide for how far one might need to look to find fringes. The relative offsets between any pair of telescopes can be calculated from the differences between the ranges. | ||
+ | |||
+ | A new baseline solution was created on 2023Jun28 and has been set as the default. The solution is based on several nights of mircx/ | ||
+ | |||
+ | S1: -0.1 mm to +0.4 mm\\ | ||
+ | S2: -0.6 mm to +0.2 mm\\ | ||
+ | E1: -0.6 mm to +0.6 mm\\ | ||
+ | E2: -0.3 mm to +0.3 mm\\ | ||
+ | W1: -0.6 mm to +0.4 mm\\ | ||
+ | W2: Reference Cart | ||
+ | |||
+ | The new solution is stored as the following backup file (also copied to telescopes.chara): | ||
+ | / | ||
+ | |||
+ | Load previous solution using the following command in ople:\\ | ||
+ | initast / | ||
+ | |||
+ | {{: | ||
+ | |||
+ | ---- | ||
+ | |||
+ | A new baseline solution was created on 2023May10 and has been set as the default. The solution is based on several nights of mircx/ | ||
+ | |||
+ | S1: -0.8 mm to +1.4 mm\\ | ||
+ | S2: -1.2 mm to +0.7 mm\\ | ||
+ | E1: -0.4 mm to +0.6 mm\\ | ||
+ | E2: -0.9 mm to +0.3 mm\\ | ||
+ | W1: -1.0 mm to +0.8 mm\\ | ||
+ | W2: Reference Cart | ||
+ | |||
+ | The new solution is stored as the following backup file (also copied to telescopes.chara): | ||
+ | / | ||
+ | |||
+ | Load previous solution using the following command in ople:\\ | ||
+ | initast / | ||
+ | |||
+ | {{: | ||
+ | |||
+ | ---- | ||
A new baseline solution was created on 2023Feb20 and has been set as the default. The solution is based on mircx/ | A new baseline solution was created on 2023Feb20 and has been set as the default. The solution is based on mircx/ | ||
Line 9: | Line 47: | ||
E1: 0.7 mm to +2.8 mm\\ | E1: 0.7 mm to +2.8 mm\\ | ||
E2: -1.0 mm to +3.0 mm\\ | E2: -1.0 mm to +3.0 mm\\ | ||
- | W1: -1.7 mm to +6.2 mm\\ | + | W1: 1.7 mm to +6.2 mm\\ |
W2: Reference Cart | W2: Reference Cart | ||
Line 18: | Line 56: | ||
initast / | initast / | ||
- | {{: | + | {{: |
---- | ---- |