chara:operating_procedures
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
chara:operating_procedures [2018/07/05 08:31] jones [Preparations in the Lab Prior to Observing] |
chara:operating_procedures [2018/07/05 08:33] jones [Setting up Computer in the Control Room] |
||
|---|---|---|---|
| Line 231: | Line 231: | ||
| \\ | \\ | ||
| + | **Chapter 3: **(edited 2012Aug29 by Gail and Chris) | ||
| ====Setting up Computer in the Control Room==== | ====Setting up Computer in the Control Room==== | ||
| - | \\ | ||
| - | (edited 2012Aug29 by Gail and Chris)\\ | ||
| \\ | \\ | ||
| ===3.1 General Overview of Computer Setup=== | ===3.1 General Overview of Computer Setup=== | ||
| Line 252: | Line 251: | ||
| \\ | \\ | ||
| ===3.2 After aligning the lab, you can turn on the following from the POWER GUI:=== | ===3.2 After aligning the lab, you can turn on the following from the POWER GUI:=== | ||
| - | \\ | ||
| \\ | \\ | ||
| Line 263: | Line 261: | ||
| \\ | \\ | ||
| ===3.3 Open servers required for observing=== | ===3.3 Open servers required for observing=== | ||
| - | \\ | ||
| \\ | \\ | ||
| Line 276: | Line 273: | ||
| * Open Metrology Laser (METLAS) gui, (upper right of screen 3), this gui usually remains open. | * Open Metrology Laser (METLAS) gui, (upper right of screen 3), this gui usually remains open. | ||
| \\ | \\ | ||
| - | ===3.4 Open Telescope GUIs from the menu===\\ | + | ===3.4 Open Telescope GUIs from the menu=== |
| | | ||
| Line 282: | Line 279: | ||
| * On the main tab for each telescope gui, click [ON] under Television to turn on the TV screen | * On the main tab for each telescope gui, click [ON] under Television to turn on the TV screen | ||
| \\ | \\ | ||
| - | ===3.5 Open GUIs required for observing from the menu under GTK:===\\ | + | ===3.5 Open GUIs required for observing from the menu under GTK:=== |
| \\ | \\ | ||
| Line 294: | Line 291: | ||
| ===3.6 Using the Cosmic Debris job sequencer=== | ===3.6 Using the Cosmic Debris job sequencer=== | ||
| \\ | \\ | ||
| - | \\ | ||
| Open Cosmic Debris, CD for short, - Primary from the menu and move to screen 4\\ | Open Cosmic Debris, CD for short, - Primary from the menu and move to screen 4\\ | ||
| \\ | \\ | ||
| Line 329: | Line 325: | ||
| ===3.7 Turn on metrology laser and home the carts=== | ===3.7 Turn on metrology laser and home the carts=== | ||
| \\ | \\ | ||
| - | \\ | ||
| Turning on the metrology laser\\ | Turning on the metrology laser\\ | ||
| Line 355: | Line 350: | ||
| \\ | \\ | ||
| ===3.8 Synchronizing the clocks=== | ===3.8 Synchronizing the clocks=== | ||
| - | \\ | ||
| \\ | \\ | ||
chara/operating_procedures.txt ยท Last modified: 2023/09/01 02:50 by gail_stargazer
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
