Differences

This shows you the differences between two versions of the page.

--- chara:trouble_shooting [2018/09/25 15:35]
gail_stargazer
+++ chara:trouble_shooting [2018/09/25 18:57]
gail_stargazer
@@ Line 59: / Line 59: @@
 ==== The Telescope won't move or stopped moving ====
- \\ Have the powers been turned on to the drives? Are the scopes disabled? The usual state of the telescopes is disabled until enabled. This is due to the stall function of the scopes which eventually disables the scopes when they are stowed. Enable the scopes by hitting [ENABLE] on the dome gui or in the telescope gui control tab. If a scope disables itself during a slew, it may be just an overcautious stall function. Hit ENABLE and the scope should continue to slew. If it disables again without moving, there may be something wrong at the scope, ie. a hatch left open, a ladder not put away, a tool on the floor, or something else physically impeding the motion of the scope. You will need to go to the dome to see what it is. The computer in the dome will give you control of the scope to turn it away from the problem. \\  \\ Sometimes the dome guis get hung up and can cause erratic motion or no motion of the scopes. Check them for current times and continuous updates of numbers. If they are not updating, try to REOPEN them first. If that does not work, close the gui and open a new one. If a new one does not open, the dome server may be dead or Sockman lost track of it. See **Dome Server Restart**  below. \\  \\ **Azimuth Limit Switches** \\  \\ As of 11-'17, the azimuth limit switches are enabled and can stop the motion of the scopes if they try to go beyond -90º or +450º. The scopes will not be movable with normal inputs so follow these instructions to return them from the out of range condition. \\  \\ 1. On the domegui MANUAL tab, click STOP so pulses won't be sent to the drive by the control software. \\  \\ 2. Make sure you understand why the limit was hit which may require a trip to the telescope. \\  \\ 3. Click the OVERRIDE ON button in domegui MANUAL tab. After this, the hardware doesn't care about the limits switches and you're free to move the telescope. \\  \\ 4. Click ENABLE then you can move the telescope back to its normal range of operation. \\  \\ 5. After the telescope is back in it normal range, click OVERRIDE OFF which makes the hardware aware of the limits again. \\
+ \\ Have the powers been turned on to the drives? Are the scopes disabled? The usual state of the telescopes is disabled until enabled. This is due to the stall function of the scopes which eventually disables the scopes when they are stowed. Enable the scopes by hitting [ENABLE] on the dome gui or in the telescope gui control tab. If a scope disables itself during a slew, it may be just an overcautious stall function. Hit ENABLE and the scope should continue to slew. If it disables again without moving, there may be something wrong at the scope, ie. a hatch left open, a ladder not put away, a tool on the floor, or something else physically impeding the motion of the scope. You will need to go to the dome to see what it is. The computer in the dome will give you control of the scope to turn it away from the problem. \\  \\ Sometimes the dome guis get hung up and can cause erratic motion or no motion of the scopes. Check them for current times and continuous updates of numbers. If they are not updating, try to REOPEN them first. If that does not work, close the gui and open a new one. If a new one does not open, the dome server may be dead or Sockman lost track of it. See **Dome Server Restart**  below. \\  \\ **Azimuth Limit Switches** \\  \\ As of 11-'17, the azimuth limit switches are enabled and can stop the motion of the scopes if they try to go beyond -90º or +450º. The scopes will not be movable with normal inputs so follow these instructions to return them from the out of range condition. \\  \\ 1. On the domegui MANUAL tab, click STOP so pulses won't be sent to the drive by the control software. \\  \\ 2. Make sure you understand why the limit was hit which may require a trip to the telescope. \\  \\ 3. Click the OVERRIDE ON button in domegui MANUAL tab. After this, the hardware doesn't care about the limits switches and you're free to move the telescope. \\  \\ 4. Click ENABLE then you can move the telescope back to its normal range of operation. \\  \\ 5. After the telescope is back in it normal range, click OVERRIDE OFF which makes the hardware aware of the limits again.
 ==== The Telescope won't track ====
@@ Line 273: / Line 273: @@
 ==== Adding or Finding a Star in the CHARA Database ====
-DBADD is a command entered in a terminal window that allows you to look up the CHARA number for a star or add a star to the CHARA database. To use dbadd, open a terminal window and type "dbadd starname" where starname is the common name (e.g., Vega) or identifier of the star (e.g., IRC, HR, HD, SAO, FK5, HIP, GJ, or 2MASS designation). If the object is in the database, then it will return the CHARA number.
+The command "dbadd" can be used to look up the CHARA number for a star or to add a star to the CHARA database. To use dbadd, open a terminal window, and type "dbadd starname" where starname is the common name (e.g., Vega) or identifier of the star (e.g., IRC, HR, HD, SAO, FK5, HIP, GJ, or 2MASS designation). If the object is in the database, then it will return the CHARA number.
 You can also look up different identifiers for the star by using the SIMBAD database: [[http://simbad.u-strasbg.fr/simbad/sim-fbasic|http://simbad.u-strasbg.fr/simbad/sim-fbasic]] \\
@@ Line 299: / Line 299: @@
 Is the above the object you are looking for? [y/n] y \\ Added "BD+41 3807" to the database.
-The object "BD+41 3807" has been added to the database as CHARA number 320414.
+In the example above, the object "BD+41 3807" has been added to the database as CHARA number 320414.
- \\ __Targets that are not in the CHARA database or in SIMBAD__ \\  \\ Some objects like recently discovered novae are not in SIMBAD. Entering dbadd <star designation> for a star not in the SIMBAD database returns the message "Simbad is unable to find an object matching <star designation>. Try using a different catalog designation, or use the "-m" switch to add the object manually." \\  \\ The command dbadd -m is used by entering the star name and coordinates in this format: \\  \\ Usage: dbadd -m <name> <RA> <Dec> \\  \\ <name>: Object ID (no spaces) \\  \\ <RA> : XXhXXmXX.X or XXhXX.X (no spaces) \\  \\ <Dec> : XXdXXmXX.X or XXdXX.X (no spaces) \\  \\ There are cases where an object is not in SIMBAD and doesn't return a result in dbadd, but is in fact in the CHARA database. Novae and AGN's are the likely objects that cause this result. At times, objects have multiple entries and several CHARA numbers since the names can be so unique. A system will be developed to find these entries without knowing or having a conventional database designation. \\  \\ __Binary stars__ \\  \\ Some binary stars have a common HD number with an A or B after them. These can cause problems as Cosmic Debris does not accept non numerical entries when filling in star designation. These stars are likely in CHARA's database but need to be searched in dbadd or on SIMBAD to get the CHARA number or another designation. \\ When a recognized identifier is entered, the HD number with A or B will usually display. Confirm that the coordinates, magnitudes and spectral type match the star desired. If they do not match, you may have the wrong star or the database may have the wrong info and the baseline solution will be affected. Offsets based on incorrect coordinates or misidentifications can move the fringes many thousands of microns away from the calculated position. This can happen when observing a dim companion (B) using the brighter (A) companion's coordinates. Inform the observers that noting and using the CHARA number will save time next time the target is observed. \\  \\ __Editing the database__ \\  \\ If you find a mistake in the database, please send an email to Nils to have it corrected. Identify what you believe to be the error and what is the correct information.
+ \\ __Targets that are not in SIMBAD__ \\  \\ Some objects like recently discovered novae are not in SIMBAD. Entering dbadd <star designation> for a star not in the SIMBAD database returns the message "Simbad is unable to find an object matching <star designation>. Try using a different catalog designation, or use the "-m" switch to add the object manually." \\  \\ The command dbadd -m is used by entering the star name and coordinates in this format: \\  \\ Usage: dbadd -m <name> <RA> <Dec> \\  \\ <name>: Object ID (no spaces) \\  \\ <RA> : XXhXXmXX.X or XXhXX.X (no spaces) \\  \\ <Dec> : XXdXXmXX.X or XXdXX.X (no spaces) \\  \\ There are cases where an object is not in SIMBAD and doesn't return a result in dbadd, but is in fact in the CHARA database. Novae and AGN's are the likely objects that cause this result. At times, objects have multiple entries and several CHARA numbers since the names can be so unique. A system will be developed to find these entries without knowing or having a conventional database designation. \\  \\ __Binary stars__ \\  \\ Some binary stars have a common HD number with an A or B after them. These can cause problems as Cosmic Debris does not accept non numerical entries when filling in star designation. These stars are likely in CHARA's database but need to be searched in dbadd or on SIMBAD to get the CHARA number or another designation.
+When a recognized identifier is entered, the HD number with A or B will usually display. Confirm that the coordinates, magnitudes and spectral type match the star desired. If they do not match, you may have the wrong star or the database may have the wrong info and the baseline solution will be affected. Offsets based on incorrect coordinates or misidentifications can move the fringes many thousands of microns away from the calculated position. This can happen when observing a dim companion (B) using the brighter (A) companion's coordinates. Inform the observers that noting and using the CHARA number will save time next time the target is observed. \\  \\ __Editing the database__ \\  \\ If you find a mistake in the database, please send an email to Nils to have it corrected. Identify what you believe to be the error and what is the correct information.
 ==== Adding an anchor to the wiki page ====

The CHARA Array Wiki

User Tools

Site Tools

Differences

Page Tools