The CHARA Array Wiki

User Tools

Site Tools

Trace:
chara:trouble_shooting

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision Both sides next revision
chara:trouble_shooting [2021/11/04 18:07]
charaobs [The Telescope won't move or stopped moving] 		chara:trouble_shooting [2021/11/04 18:12]
charaobs [The Telescope won't move or stopped moving]
Line 102: Line 102:
 <font 14px/Arial,Helvetica,sans-serif;;#333333;;white>1. On the domegui MANUAL tab, click STOP so pulses won't be sent to the drive by the control software.</font>  \\ <font 14px/Arial,Helvetica,sans-serif;;#333333;;white>1. On the domegui MANUAL tab, click STOP so pulses won't be sent to the drive by the control software.</font>  \\
 \\ \\
-<font inherit/inherit;;initial;;white>2. M</font> ake sure the all the scopes’ demand positions agree – for example, sometimes bringing a scope to a configuration that’s already on sky and issuing a slew command will make the additional scope go around North the “wrong” way.\\+<font inherit/inherit;;initial;;white>2. M</font>ake sure the all the scopes’ demand positions agree – for example, sometimes bringing a scope to a configuration that’s already on sky and issuing a slew command will make the additional scope go around North the “wrong” way.\\
 \\ \\
 <font inherit/inherit;;initial;;white>3. Click the OVERRIDE ON button in domegui MANUAL tab.</font> <font inherit/inherit;;initial;;white>3. Click the OVERRIDE ON button in domegui MANUAL tab.</font>
  
-<font 14px/Arial,Helvetica,sans-serif;;#333333;;inherit>4. Move the scope a bit back toward the direction it was coming from – for example, if it stopped at AZ 268 while rotating clockwise, move it back to 265 or so using AZ DEC. Then press STOP.</font>+<font 14px/Arial,Helvetica,sans-serif;;#333333;;inherit>4. Move the scope a bit back toward the direction it was coming from – for example, if the scope stopped at AZ 268 while rotating clockwise, move it back to 265 or so using AZ DEC. Then press STOP.</font>
  
 <font 14px/Arial,Helvetica,sans-serif;;#333333;;inherit>5. Move the scope past AZ 270 by pressing AC INC. Usally 2-4 degrees will do.</font> <font 14px/Arial,Helvetica,sans-serif;;#333333;;inherit>5. Move the scope past AZ 270 by pressing AC INC. Usally 2-4 degrees will do.</font>
Line 112: Line 112:
 <font 14px/Arial,Helvetica,sans-serif;;#333333;;inherit>6. Click OVERRIDE OFF, go to the AUTO tab and press AUTO, then NEXT (also in the obsgtk; this will restore the original star's demand position to the scope).</font> <font 14px/Arial,Helvetica,sans-serif;;#333333;;inherit>6. Click OVERRIDE OFF, go to the AUTO tab and press AUTO, then NEXT (also in the obsgtk; this will restore the original star's demand position to the scope).</font>
  
-<font 14px/Arial,Helvetica,sans-serif;;#333333;;inherit>7. When you have time, go to the scope and reset the limit switch.</font>+<font 14px/Arial,Helvetica,sans-serif;;#333333;;inherit>7. When you have time, go to the scope and reset the limit switch; otherwise, it will stop each time you pass AZ 270/90.</font>
  
  
chara/trouble_shooting.txt · Last modified: 2024/06/18 00:21 by charaobs

Page Tools

Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
CC Attribution-Share Alike 4.0 International Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki