This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
chara:trouble_shooting [2021/11/09 14:16] gail_stargazer |
chara:trouble_shooting [2021/11/09 14:41] gail_stargazer |
||
---|---|---|---|
Line 201: | Line 201: | ||
===== HUT servers ===== | ===== HUT servers ===== | ||
+ | |||
+ | ==== I can't change the camera settings on the TV ==== | ||
+ | |||
+ | **CHECK THIS SECTION - THESE ARE VERY CLOSE BUT DIFFERENT PARAGRAPHS: | ||
The HUT servers control functions such as beacon and dichroic movements, heater and dehumidifier usage, and various AO functions. An observer may find that the obsgtk is no longer controlling the beacon LED's, beacon flat or dichroic alignments. This happens on occasion with E2 and other scopes. The HUT server may be the cause if it has quit or lost connection or the AOB may be at fault. To see if it is the server, open the HUT gui for the desired telescope from the CHARA menu. If the alignments can be changed from the gui, then the HUT server is ok. You can use the hut gui to continue observing. If the hut gui gives move error messages, cycle the power on the AOB and open a new hut server to restore the connection to the obsgtk. On the POWER gui, turn off the power to the AOB for the offending telescope and turn it back on. Stop the hut server by logging into the appropriate telescope computer and identifying the PID with the bootlaunch_master command and killing the process with the kill -9 #### command. Start the new server via the bootlaunch_master command. Hit REOPEN on the obsgtk to reopen the connection to the HUT server and hit reopen on Cosmic Debris as well. | The HUT servers control functions such as beacon and dichroic movements, heater and dehumidifier usage, and various AO functions. An observer may find that the obsgtk is no longer controlling the beacon LED's, beacon flat or dichroic alignments. This happens on occasion with E2 and other scopes. The HUT server may be the cause if it has quit or lost connection or the AOB may be at fault. To see if it is the server, open the HUT gui for the desired telescope from the CHARA menu. If the alignments can be changed from the gui, then the HUT server is ok. You can use the hut gui to continue observing. If the hut gui gives move error messages, cycle the power on the AOB and open a new hut server to restore the connection to the obsgtk. On the POWER gui, turn off the power to the AOB for the offending telescope and turn it back on. Stop the hut server by logging into the appropriate telescope computer and identifying the PID with the bootlaunch_master command and killing the process with the kill -9 #### command. Start the new server via the bootlaunch_master command. Hit REOPEN on the obsgtk to reopen the connection to the HUT server and hit reopen on Cosmic Debris as well. | ||
+ | |||
+ | The HUT servers control functions such as finder and acq exposure times and gains, heater and dehumidifier usage, and various AO functions. An observer may find that the camera settings do not display or are not adjustable. The HUT server may be the cause if it has quit. To see if it is the server, open the HUT gui for the desired telescope from the CHARA menu. If the camera settings are displayed and the settings can be changed from the gui, then the HUT server is ok. Restart the telescope server to reopen the connection to the HUT server and hit reopen on Cosmic Debris as well. If the gui is not functioning, | ||
+ | |||
+ | If the server won't restart, a reboot of the power supply in the telescope bunker might be necessary. The power supply that controls the acquisition and finder cameras as well as their controllers is located on top of the computer rack in each bunker. The power supply has green readouts of volts and current. After turning the power off for 10 seconds and back on, try restarting the server from the computer in the bunker to see if it starts cleanly. If so, then restart the telescope server, reopen the connection to the telescope gui, and hit REOPEN on Cosmic Debris. Part of the HUT server also controls the AO table. If the AOB part of the HUT server doesn' | ||
===== Tiptilt Server. (These sections apply to the old lab tiptilt system retired in April 2021) ===== | ===== Tiptilt Server. (These sections apply to the old lab tiptilt system retired in April 2021) ===== | ||
+ | |||
+ | [[: | ||
The tiptilt server controls the CCD based tiptilt detection system. \\ \\ | The tiptilt server controls the CCD based tiptilt detection system. \\ \\ | ||
Line 305: | Line 315: | ||
==== Restarting the Beam Sampler Server ==== | ==== Restarting the Beam Sampler Server ==== | ||
- | The most common cause for getting multiple copies of a server is using the socket manage RESTART button, which is flaky at best. Don't do this. If you need to restart a server you should do it manually. 1. Make sure you are logged into the right machine: ssh ctrscrut 2. If you are not sure see if the socket manager will tell you. If it doesn' | + | The most common cause for getting multiple copies of a server is using the socket manage RESTART button, which is flaky at best. Don't do this. If you need to restart a server you should do it manually. |
+ | |||
+ | 1. Make sure you are logged into the right machine: ssh ctrscrut | ||
+ | |||
+ | 2. If you are not sure see if the socket manager will tell you. If it doesn' | ||
+ | |||
+ | 3. See if there are any ghosts running ps aux | grep esp_server Yes, it's hard to know which one it is with the esp servers. You can work out which ones are ghosts by typing the command tsockman |grep ctrscrut which will give you a list of the servers running on the machine you are interested in. Checking for non-matching PIDs will tell you which processes you need to stop. | ||
+ | |||
+ | 4. Stop those processes: kill -9 PID1 PID2 …. 5. Make sure there is no sign of it in the socket manager tsockman rm BS | ||
+ | |||
+ | 5. Restart the beam sampler servers (this starts both beam sampler servers BS1 and BS2): bootlaunch_beamsamp | ||
==== " | ==== " | ||
Line 360: | Line 380: | ||
If an object is not in SIMBAD (such as a recently discovered nova), then you must enter the object manually using the instructions below. | If an object is not in SIMBAD (such as a recently discovered nova), then you must enter the object manually using the instructions below. | ||
- | ==== Finding a star in the CHARA database | + | **Finding a star in the CHARA database** |
Here is an example of how to find the CHARA number of a star, nova, or AGN that is already in the CHARA database: | Here is an example of how to find the CHARA number of a star, nova, or AGN that is already in the CHARA database: |