This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
chara:trouble_shooting [2022/01/21 20:03] charaobs |
chara:trouble_shooting [2022/02/09 19:10] charaobs |
||
---|---|---|---|
Line 9: | Line 9: | ||
* Were the clocks synced? Make sure the [SYNC CLOCKS] button on Cosmic Debris has been pushed to start the night. If the OPLE server does not display the correct CHARA time and the errors don't read (0) or (1), the clocks were not synced. | * Were the clocks synced? Make sure the [SYNC CLOCKS] button on Cosmic Debris has been pushed to start the night. If the OPLE server does not display the correct CHARA time and the errors don't read (0) or (1), the clocks were not synced. | ||
- | * Did the Astrolib update on OPLE? If the job queue is stopped too soon after slewing on Cosmic Debris, the correct calculations for the carts will not be done by OPLE and you may be searching for fringes with the wrong star data. Hit STAR ACQUIRED on CD to update | + | * Did the Astrolib update on OPLE? If the job queue is stopped too soon after slewing on Cosmic Debris, the correct calculations for the carts will not be done by OPLE and you may be searching for fringes with the wrong star data. The star identifier will be displayed in the server window. If it is not correct, hit STAR ACQUIRED on CD to update |
- | * Are the PoP's correct? After a PoP change, the PoP's are sometimes not updated in CD or ople. | + | * Are the PoP's correct? After a PoP change, the PoP's are sometimes not updated in CD or ople. Compare the PoP's in the configuration tab of CD or OPLE with the PoP Overview or Popperi gtk. |
* Are the carts behaving or are there vibrations or jumps of 100 or more microns every 3-6 seconds? How are the metrology signals? Are they strong and staying white? Red signals mean one or more metrology signals may have gone too low and homing carts is necessary. The METDATA function on the ople gui can be used to sample the metrology signal and may show noise spikes that can be disruptive to the smooth cart motion. Push the METDATA button on the configure tab and then again about 6 seconds later. Plots will pop up to show the frequency and power of any noise. | * Are the carts behaving or are there vibrations or jumps of 100 or more microns every 3-6 seconds? How are the metrology signals? Are they strong and staying white? Red signals mean one or more metrology signals may have gone too low and homing carts is necessary. The METDATA function on the ople gui can be used to sample the metrology signal and may show noise spikes that can be disruptive to the smooth cart motion. Push the METDATA button on the configure tab and then again about 6 seconds later. Plots will pop up to show the frequency and power of any noise. | ||
* Is the target a high proper motion star? Red dwarfs are close stars and can have high proper motions. Scan a wider range to see if it is outside of the usual calculated scan range. Binaries can also have very high offsets from the expected position due to mistakenly using astromod calculations from the companion star. | * Is the target a high proper motion star? Red dwarfs are close stars and can have high proper motions. Scan a wider range to see if it is outside of the usual calculated scan range. Binaries can also have very high offsets from the expected position due to mistakenly using astromod calculations from the companion star. | ||
- | * Do you have enough flux from each telescope or on each baseline? Is the telescope tiptilt struggling with low flux? Can the camera gain be raised or the exposure made longer to help hold the star? | + | * Do you have enough flux from each telescope or on each baseline? Is the telescope tiptilt struggling with low flux? Can the camera gain be raised or the exposure made longer to help hold the star? Passing clouds or contrails can lower flux unexpectedly. |
* Did you get the same star in each telescope? Sometimes a busy star field and poor pointing of the telescopes can lead to the wrong star being acquired and locked by tiptilt. View the stars in the finder window to see if all the stars match. | * Did you get the same star in each telescope? Sometimes a busy star field and poor pointing of the telescopes can lead to the wrong star being acquired and locked by tiptilt. View the stars in the finder window to see if all the stars match. | ||
* Check the CHARA time on the GPS server. The " | * Check the CHARA time on the GPS server. The " | ||
* Check the time on the OPLE server. If the time is off or there are any lost ticks/ | * Check the time on the OPLE server. If the time is off or there are any lost ticks/ | ||
* Are the [MAN] buttons pressed (gray) for the moving carts on the OPLE Control gui? (The reference cart will remain green.) | * Are the [MAN] buttons pressed (gray) for the moving carts on the OPLE Control gui? (The reference cart will remain green.) | ||
- | * Check that the carts are within delay line range (-1 to 44 meters) and errors are small. Were the carts homed and checked before the first slew of the night? Did any carts go to the front switch after slewing? This can cause them to lose their position. Turn off the OL button to send it back to zero. If it does not track on the home switch when displaying a zero position (0.000000), it was lost. Is the E2 cart stuck at 27.97m? See section on homing carts in __OPLE and Metrology__ | + | * Check that the carts are within delay line range (-1.3 to 44.25 meters) and errors are small. Were the carts homed and checked before the first slew of the night? Did any carts go to the front switch after slewing? This can cause them to lose their position. Turn off the OL button to send it back to zero. If it does not track on the home switch when displaying a zero position (0.000000), it was lost. Is the E2 cart stuck at 27.97m? See section on homing carts in __OPLE and Metrology__ |
* Are the LDC's working? | * Are the LDC's working? | ||
* Is the glass position within allowable range (-10mm to 49mm) on all beams? | * Is the glass position within allowable range (-10mm to 49mm) on all beams? | ||
Line 90: | Line 90: | ||
<font 14px/ | <font 14px/ | ||
- | <font 14px/ | + | <font 14px/ |
<font 14px/ | <font 14px/ | ||
Line 106: | Line 106: | ||
==== Dome Server Restart ==== | ==== Dome Server Restart ==== | ||
- | Dome servers are now started using the bootlaunch_master command. | + | Dome servers are now started using the bootlaunch_master command. The manual process that has been superceded is archived. |
To restart the dome server: | To restart the dome server: | ||
- | 1. Make sure the power to the drives is OFF. Disable the scopes. | + | 1. Make sure the power to the drives is OFF. Disable the scopes. |
2. Login to the relevant computer as observe. For example, type " | 2. Login to the relevant computer as observe. For example, type " | ||
Line 116: | Line 116: | ||
3. Work out the process ID number (PID) by typing bootlaunch_master | 3. Work out the process ID number (PID) by typing bootlaunch_master | ||
- | 4. Use kill -2 PID to kill the server. | + | 4. Use kill -2 PID to kill the server. Entering the command twice will show "No such process" |
5. Type bootlaunch_master again to restart the server. | 5. Type bootlaunch_master again to restart the server. | ||
Line 296: | Line 296: | ||
* If the top of a server goes blank, try typing " | * If the top of a server goes blank, try typing " | ||
* If the server screen fills with jibberish, try hitting CTRL-L in the server to clear it. | * If the server screen fills with jibberish, try hitting CTRL-L in the server to clear it. | ||
+ | * If a server freezes, sometimes hitting CTRL-C and then N, for NO, will unfreeze it. | ||
==== Server is frozen ==== | ==== Server is frozen ==== | ||
Line 305: | Line 306: | ||
* Click [REOPEN] on Cosmic Debris and relevant GUIs to re-initialize communication with the server after it is restarted. | * Click [REOPEN] on Cosmic Debris and relevant GUIs to re-initialize communication with the server after it is restarted. | ||
* A folder is on the desktop that has the restart commands for CTRSCRUT servers and the Shutters server restart command running on OPLE. Use it to restart servers that will not reopen from the menu. | * A folder is on the desktop that has the restart commands for CTRSCRUT servers and the Shutters server restart command running on OPLE. Use it to restart servers that will not reopen from the menu. | ||
+ | * if a telescope server does not close after using CTRL-C when restarting them after UT midnight and the Send ON button is green on the obsgtk, turn the Send ON to OFF and the server will close. | ||
==== PAVO Server - Error communicating with IFW ==== | ==== PAVO Server - Error communicating with IFW ==== |