chara:coude_alignment_procedure
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
chara:coude_alignment_procedure [2021/06/02 19:00] gail_stargazer |
chara:coude_alignment_procedure [2024/05/07 19:53] (current) charaobs [Udated 2024 May 6] |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ===== Coude Alignment Procedure ===== | ===== Coude Alignment Procedure ===== | ||
| - | Written by Judit Sturmann on 2021 June 1. | + | ==== Updated 2024 May 6 ==== |
| - | ==== Preparation | + | <font 12pt/ |
| + | |||
| + | - Start with an M10 alignment before beginning the coude process (usually done on POP 5) | ||
| + | - Send M7's to default | ||
| + | - Do regular beginning of the night alignment procedure | ||
| + | - align beacon, dichroic, focus labao, focus wfs | ||
| + | - Open an engineering hut GUI: >> hutgtk -E S1 & | ||
| + | - AOB ENG tab | ||
| + | - note the M7_1 and M7_2 actuator positions and enter them on the Excel page. | ||
| + | - Select and hit **[GET].** | ||
| + | - Value reads below get and should match last entry on excel | ||
| + | - Turn powers on and enable scope(s) | ||
| + | - Dome GUI, Auto tab: | ||
| + | - On 'Az Pos', enter the stow position + 180 | ||
| + | - **[Set Pos]** | ||
| + | - Watch beacon spots and use M7 to keep them centered while it rotates 180°. | ||
| + | - Obsgtk, align M7 when it stops moving. | ||
| + | - Hut GUI, note new M7_1 and M_2 values and enter in excel. | ||
| + | - ignore last 3 digits and record first 4 | ||
| + | - spreadsheet will calculate the average value | ||
| + | - enter the average value + 3 zeros for each actuator (M7_1 and M7_2). | ||
| + | - If its a large move, watch the beacon spots as they move away because you will need to recenter them | ||
| + | - Use the dichroic to realign the beacon to labao | ||
| + | - Hit **[STOW]** | ||
| + | - The beacon movement should be much smaller returning to stow than it was going away from stow | ||
| + | - Align M7 | ||
| + | - Enter new actuator positions into excel | ||
| + | - Hut GUI, send both actuators to calculated position. | ||
| + | - Align dichroic | ||
| + | - if the beacon movements were small on the way back to stow, then the coude alignment is finished. If it wasn' | ||
| + | - Hut GUI, save the new M7 dichroic positions by hitting **[DICHR POS] **then **[WRITE CFG]** | ||
| + | - it will save them to / | ||
| + | - Can enter any notes on why coude alignment was needed on excel sheet. | ||
| + | |||
| + | |||
| + | ==== Updated 2021Jun01 by Judit: | ||
| + | |||
| + | === Preparation === | ||
| + | |||
| + | Make sure the vacuum is below 5 torr in the pipe. | ||
| - | * Make sure the vacuum is below 5 torr in the pipe. | ||
| * Proceed with the usual steps up to LAB DICH alignment with labao. | * Proceed with the usual steps up to LAB DICH alignment with labao. | ||
| * Adjust by hand DM tilt to front side of front rail target | * Adjust by hand DM tilt to front side of front rail target | ||
| Line 22: | Line 60: | ||
| As of 6/1/2021 only E2 has the new cones. | As of 6/1/2021 only E2 has the new cones. | ||
| + | |||
| ==== M7 adjustment based on laser in AQUISITION camera ==== | ==== M7 adjustment based on laser in AQUISITION camera ==== | ||
| Line 52: | Line 91: | ||
| ==== Revision History ==== | ==== Revision History ==== | ||
| - | * Document written by Judit Sturmann | + | * 2021Jun01 - Document written by Judit Sturmann. |
| - | * Gail Schaefer added to wiki page on 6/2/2021. | + | * 2021Jun02 - Gail Schaefer added to wiki page. |
| + | * 2021Jun02 - Removed link for [[https://docs.google.com/ | ||
| + | * 2021Jun02 - Remove link for [[: | ||
chara/coude_alignment_procedure.1622674813.txt.gz · Last modified: 2021/06/02 19:00 by gail_stargazer
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
