This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
chara:new_operating_procedures [2024/06/14 18:06] bflores [Common Issues] |
chara:new_operating_procedures [2024/08/07 20:02] (current) bflores [The Next Slew - Avoid Triggering AZ Limit Switches:] |
||
---|---|---|---|
Line 1: | Line 1: | ||
====== New Operating Procedures ====== | ====== New Operating Procedures ====== | ||
- | Last updated | + | Last updated |
[[: | [[: | ||
Line 45: | Line 45: | ||
[[: | [[: | ||
[[: | [[: | ||
- | [[http:// | + | [[http:// |
+ | [[: | ||
\\ __**ADAPTIVE OPTICS DOCUMENTATION**__ | \\ __**ADAPTIVE OPTICS DOCUMENTATION**__ | ||
Line 85: | Line 86: | ||
==== Dust ==== | ==== Dust ==== | ||
+ | |||
+ | First thing to check are the purple air particulate sensors. There are three (S1E1W1) and will give a fairly good representation of the number of particulates in the area. The baseline fluctuates somewhat, and the shutdown numbers are yet to be determined. The default is PM2.5 EPA AQI and should check other methods if the number is over 50-100 (needs calibration). Please find the map at the following link: | ||
+ | |||
+ | [[https:// | ||
Gauging the airborne dust and pollen can be problematic because you need a bright light and a relatively dark night. In general, you want to look in the bottom 0.5 meter of the light column. There will be a diffuse column lit up by the beam – don’t worry about it, just follow the dust glints. If you can count the dust glints, the conditions are safe to observe. If it looks like a blizzard, close up. If any of the dust glints shine with an orange or a peach hue, or the dust glints look abnormally large, the dust is probably ash – close up immediately. Ash seriously degrades bare aluminum coatings. Dust and wind go together. But, just because it is calm, the dust conditions might still be bad. If it was windy a few days earlier, it could have kicked up a lot of dust, which can take several days to settle. Finally, during late spring to early summer, conifer tree pollen can be problematic. If particulates are borderline please email the CHARA day staff so they can clean the optics as soon as possible. | Gauging the airborne dust and pollen can be problematic because you need a bright light and a relatively dark night. In general, you want to look in the bottom 0.5 meter of the light column. There will be a diffuse column lit up by the beam – don’t worry about it, just follow the dust glints. If you can count the dust glints, the conditions are safe to observe. If it looks like a blizzard, close up. If any of the dust glints shine with an orange or a peach hue, or the dust glints look abnormally large, the dust is probably ash – close up immediately. Ash seriously degrades bare aluminum coatings. Dust and wind go together. But, just because it is calm, the dust conditions might still be bad. If it was windy a few days earlier, it could have kicked up a lot of dust, which can take several days to settle. Finally, during late spring to early summer, conifer tree pollen can be problematic. If particulates are borderline please email the CHARA day staff so they can clean the optics as soon as possible. | ||
Line 135: | Line 140: | ||
===== Sunset Prep ===== | ===== Sunset Prep ===== | ||
- | ==== Opening the telescope domes and enclosures | + | ==== Opening the telescope domes and cylinders |
- | Begin opening telescope domes and enclosures | + | Begin opening telescope domes and cylinders |
+ | |||
+ | Currently, only S2 and W1 can have the lower cylinders opened. | ||
Before opening the domes, make sure to check the current weather conditions and the forecast to make sure conditions are safe to open and are likely to be stable as you wait for it to get dark. | Before opening the domes, make sure to check the current weather conditions and the forecast to make sure conditions are safe to open and are likely to be stable as you wait for it to get dark. | ||
Line 143: | Line 150: | ||
__To vent the domes (open partially, usually during Summertime): | __To vent the domes (open partially, usually during Summertime): | ||
- | | + | - On **obsgtk**, control tab, **[UNL SL], [VENT] ** |
- Open them fully when the sun has reached 40º for maximum cooling. The time you can fully open is on the white board, | - Open them fully when the sun has reached 40º for maximum cooling. The time you can fully open is on the white board, | ||
- Then** Dome GUI, RA/DEC tab, ANTI-SUN** | - Then** Dome GUI, RA/DEC tab, ANTI-SUN** | ||
Line 153: | Line 160: | ||
* Monitor the progress of opening the domes: | * Monitor the progress of opening the domes: | ||
* **Obsgtk, [ON], [SPY1]** | * **Obsgtk, [ON], [SPY1]** | ||
+ | __To open the cylinders: | ||
+ | |||
+ | - In a terminal, " | ||
+ | - Control tab, **[Low Open] ** | ||
+ | - do for each cylinder (currently only S2 and W1) | ||
+ | - Check status of each cylinder with each tab (S2 or W1) | ||
+ | - Should say "Lower cylinder: Opening/ | ||
+ | |||
===== ===== | ===== ===== | ||
+ | |||
===== Preparations in the Lab Prior to Observing ===== | ===== Preparations in the Lab Prior to Observing ===== | ||
Line 171: | Line 187: | ||
- S1 and S2 lines leak the most, so open first until they reach the level of the next highest pressure line (usually E1, then W2). Can open all the valves once they are low enough ( ~3 torr or so). | - S1 and S2 lines leak the most, so open first until they reach the level of the next highest pressure line (usually E1, then W2). Can open all the valves once they are low enough ( ~3 torr or so). | ||
- If pressure is higher than 100 torr in any of the lines, pump those lines only one at a time. | - If pressure is higher than 100 torr in any of the lines, pump those lines only one at a time. | ||
- | |||
==== Turn on Electronics Inside the Lab ==== | ==== Turn on Electronics Inside the Lab ==== | ||
Line 192: | Line 207: | ||
Day time staff will align the lab during the week, but operator is responsible for alignments on the weekends. | Day time staff will align the lab during the week, but operator is responsible for alignments on the weekends. | ||
- | Before doing alignments, | + | Before doing alignments, |
- | - Blue chara menu, ESP Controllers, | + | |
- Turn on each scope ldc (red button will turn green) | - Turn on each scope ldc (red button will turn green) | ||
- change ' | - change ' | ||
Line 302: | Line 317: | ||
- go inside lab to where STS is set up. On the wall outlet, plug in the black cord; it's the only cord by the outlet. | - go inside lab to where STS is set up. On the wall outlet, plug in the black cord; it's the only cord by the outlet. | ||
- use GUI " | - use GUI " | ||
- | |||
==== Starting OPLE System and Metrology ==== | ==== Starting OPLE System and Metrology ==== | ||
Line 359: | Line 373: | ||
- To reorganize the servers - White menu, load layout, press mouse wheel, enter, all servers will go to saved positions. | - To reorganize the servers - White menu, load layout, press mouse wheel, enter, all servers will go to saved positions. | ||
- Or highlight the last entry on 2nd column and press the scroll wheel to paste, then enter. | - Or highlight the last entry on 2nd column and press the scroll wheel to paste, then enter. | ||
- | |||
==== Setting up GUIs for observing: ==== | ==== Setting up GUIs for observing: ==== | ||
Line 495: | Line 508: | ||
- use **[STAND]** | - use **[STAND]** | ||
- [Stand] will automatically turn on the camera | - [Stand] will automatically turn on the camera | ||
- | - use **[BRIGHT] ** (Gain 90) for VIS programs, W2 and S1 can stay at Gain 300 as they are very dim. | + | - use **[BRIGHT] ** (Gain 90) for VIS programs, W2 and S1 can stay at Gain 300 as they are very dim. |
- to use a different gain, have to manually set: | - to use a different gain, have to manually set: | ||
- **[USBOFF]**, | - **[USBOFF]**, | ||
Line 522: | Line 535: | ||
- Bootlaunch_master twice to make sure it is removed from sockman and a new acq server started | - Bootlaunch_master twice to make sure it is removed from sockman and a new acq server started | ||
- Reopen obsgtk and turn on Acq view | - Reopen obsgtk and turn on Acq view | ||
- | |||
==== Beacon Alignment/ | ==== Beacon Alignment/ | ||
Line 536: | Line 548: | ||
- Load default flat on __tel WFS__ | - Load default flat on __tel WFS__ | ||
- Main tab, **[****LD DEF].** | - Main tab, **[****LD DEF].** | ||
- | - Confirm DM curent changes when loading the default. Should range between 0.76-1.61A | + | - Confirm DM curent changes when loading the default. Should range between 0.64-2.28A |
- Make sure DMTILT is on | - Make sure DMTILT is on | ||
- Main tab, **[DMTILT]**, | - Main tab, **[DMTILT]**, | ||
Line 576: | Line 588: | ||
- Can repeat as you wait for the sky to get dark. | - Can repeat as you wait for the sky to get dark. | ||
- Make sure to repeat alignments (ALN BCN, ALN DIC, FOCUS, FOCUS) __before slewing__. The optics will drift as the AO board thermally cools after the domes are opened. | - Make sure to repeat alignments (ALN BCN, ALN DIC, FOCUS, FOCUS) __before slewing__. The optics will drift as the AO board thermally cools after the domes are opened. | ||
- | |||
==== SPICA STS ==== | ==== SPICA STS ==== | ||
Line 618: | Line 629: | ||
- On shutgtk, click on **[STST] **to put the stage into the beam path. | - On shutgtk, click on **[STST] **to put the stage into the beam path. | ||
- On mircx_super_gtk, | - On mircx_super_gtk, | ||
- | - Open the Star Tracker gui by typing **“ststrtd_gtk”**in a terminal. | + | - Open the Star Tracker gui by typing **“ststrtd_gtk”**in a terminal |
- Config camera needed. The default settings are good to Hmag 5 or so. | - Config camera needed. The default settings are good to Hmag 5 or so. | ||
- press **[Start Camera]** | - press **[Start Camera]** | ||
- Click **[Start RTD] **to start the display. | - Click **[Start RTD] **to start the display. | ||
- if gui is not responding, restart stst server | - if gui is not responding, restart stst server | ||
- | - ssh -X spooler@stst | + | - ssh spooler@stst |
- | - killall mircx_stst_server | + | - kill_stst, then run_stst |
- | - mircx_bootLaunch, type ' | + | - Take backgrounds if the display is not evenly |
- | - Take backgrounds if the display is not evenbackly | + | |
- Select “Image” from filter menu. | - Select “Image” from filter menu. | ||
- if you don't see anything | - if you don't see anything | ||
Line 682: | Line 692: | ||
- The **[MAN] **button for **the reference cart** | - The **[MAN] **button for **the reference cart** | ||
- Click **[TRACK] **on the OPLE Control Tab **for all active carts, | - Click **[TRACK] **on the OPLE Control Tab **for all active carts, | ||
- | |||
===== Going on Sky ===== | ===== Going on Sky ===== | ||
Line 696: | Line 705: | ||
- **Obsgtk**, Control Tab, open mirror covers. Click only one cover at a time and wait for it to open. Click each button only once, do not click repeatedly: | - **Obsgtk**, Control Tab, open mirror covers. Click only one cover at a time and wait for it to open. Click each button only once, do not click repeatedly: | ||
- | - [M1 OPEN] - opens the primary mirror cover (takes ~ 3 minutes to open) | + | - [M1 OPEN] - opens the primary mirror cover (takes ~ 3 minutes to open) Only open after 20 minutes after sunset. |
- | - [M3 OPEN] | + | - [M3 OPEN] Same as above. |
- [M5 OPEN] - if not already open | - [M5 OPEN] - if not already open | ||
- [M7 OPEN] - if not already open | - [M7 OPEN] - if not already open | ||
Line 706: | Line 715: | ||
==== Final Alignment Before Slewing ==== | ==== Final Alignment Before Slewing ==== | ||
- | - While still at stow, align red and blue beacon and bring focus terms to zero. | + | - While still at stow, align red and blue beacon and bring focus terms to zero. Be aware that SPICA sees the red beacon and may want it off when they do STS recording. |
- | - **[ZCEN]** | + | - **[ZCEN]** |
==== Enabling The Telescopes ==== | ==== Enabling The Telescopes ==== | ||
Line 766: | Line 775: | ||
- **PAVO/ | - **PAVO/ | ||
- The [MAN] button for the reference cart should be green. | - The [MAN] button for the reference cart should be green. | ||
- | |||
==== Locking on a Target ==== | ==== Locking on a Target ==== | ||
Line 797: | Line 805: | ||
For the visible combiners the red beacon and starlight will be coaligned, so you only need to use the blue starlight boxes on the telescope WFS. | For the visible combiners the red beacon and starlight will be coaligned, so you only need to use the blue starlight boxes on the telescope WFS. | ||
- | **Obsgtk, **main tab, **[ZERO BCN]** at the start of the night to clear any offset between the position of the beacon boxes and the starlight boxes to avoid any confustion | + | **Obsgtk, **main tab, **[ZERO BCN]** |
For **SPICA**, make sure to do " | For **SPICA**, make sure to do " | ||
- | - Slew to star. | + | |
- Main tab, turn on **[M7AUTO] **to hold the blue beacon during the slew and avoid drifting. It will turn off at the end of the slew. | - Main tab, turn on **[M7AUTO] **to hold the blue beacon during the slew and avoid drifting. It will turn off at the end of the slew. | ||
- CD, **[Star Acquired], | - CD, **[Star Acquired], | ||
Line 844: | Line 852: | ||
- At times, Mircx will have such poor flux that a beacon flat correction to align to the STST reference position will be needed. This will occur on **E1 pop 4 ****and 5** and **S1 pop 5** due to their extreme distances from the telescope to the lab. | - At times, Mircx will have such poor flux that a beacon flat correction to align to the STST reference position will be needed. This will occur on **E1 pop 4 ****and 5** and **S1 pop 5** due to their extreme distances from the telescope to the lab. | ||
- Follow the SPICA team guidance in making this correction to improve the flux to keep Mircx usable as a fringe tracker with those baselines. | - Follow the SPICA team guidance in making this correction to improve the flux to keep Mircx usable as a fringe tracker with those baselines. | ||
- | |||
==== Alignment Sequence for IR Combiners: MIRC-X/ | ==== Alignment Sequence for IR Combiners: MIRC-X/ | ||
Line 1002: | Line 1009: | ||
- Note: ADDAB now works for astigmatism and coma terms. | - Note: ADDAB now works for astigmatism and coma terms. | ||
- | ===== The Next Slew - Avoid Limit Switch Issues Near AZ 0º: ===== | + | ===== The Next Slew - Avoid Triggering |
Always pay attention to the AZ you are slewing from or to, to avoid passing the sensors incorrectly and dealing with scopes getting stuck near 90° or 270°. | Always pay attention to the AZ you are slewing from or to, to avoid passing the sensors incorrectly and dealing with scopes getting stuck near 90° or 270°. | ||
+ | |||
+ | __Az Limit Switch Near 0º:__ | ||
There are two sensors negative and positive near AZ 0. | There are two sensors negative and positive near AZ 0. | ||
Line 1019: | Line 1028: | ||
* now you can slew back the other way to the next target. | * now you can slew back the other way to the next target. | ||
- | If you don't pay attention and only hit one sensor at AZ 0, some or all telescopes will continue to stall near 90 or 270 degrees and it is a pain to fix. | + | If you don't pay attention and only hit one sensor at AZ 0, some or all telescopes will continue to stall near 90 or 270 degrees and it is a pain to fix. Will have to trip the limit switch at the telescope. |
+ | |||
+ | __TCS Az limit beyond -90 and 450º: __ | ||
+ | |||
+ | On the telescope server, keep an eye on the TCS az to not go beyond -90º and 450º. If you are getting close, telescopes will have to go the other way around to avoid hitting the limit. | ||
+ | |||
+ | * can send to STOW or to another star using FIND* on obsgtk. | ||
Got to [[: | Got to [[: | ||
+ | |||
===== Additional Observing Procedures ===== | ===== Additional Observing Procedures ===== | ||
Line 1154: | Line 1170: | ||
- Turn off WFS COOL when Matt requests it. | - Turn off WFS COOL when Matt requests it. | ||
- Never do camerlink off | - Never do camerlink off | ||
- | - Obsgtk, MAIN→ | + | - Obsgtk, MAIN→ Labao STOP OFF |
- Shutdown STST | - Shutdown STST | ||
- | - Click the “Start Camera” button to turn off the camera (the button will go from green to gray). | + | - Click the “Start Camera” |
- Change the filter wheel to the closed position. | - Change the filter wheel to the closed position. | ||
- Using the shutter gtk, remove the STST stage from the beams. | - Using the shutter gtk, remove the STST stage from the beams. |