User Tools

Site Tools


chara:new_operating_procedures

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
chara:new_operating_procedures [2024/08/07 19:39]
bflores [New Operating Procedures]
chara:new_operating_procedures [2024/08/07 20:02] (current)
bflores [The Next Slew - Avoid Triggering AZ Limit Switches:]
Line 160: Line 160:
   * Monitor the progress of opening the domes:   * Monitor the progress of opening the domes:
       * **Obsgtk, [ON], [SPY1]**       * **Obsgtk, [ON], [SPY1]**
-To open the cylinders:+__To open the cylinders:__
  
-  - in a terminal, "cylinder_new_gtk &"+  - In a terminal, "cylinder_new_gtk &"
   - Control tab, **[Low Open] **   - Control tab, **[Low Open] **
       - do for each cylinder (currently only S2 and W1)       - do for each cylinder (currently only S2 and W1)
-  - can click on each tab (S2 or W1) to check the status of the cylinder. Should say "Lower cylinder: Opening/Open".+  - Check status of each cylinder with each tab (S2 or W1) 
 +      - Should say "Lower cylinder: Opening/Open/Closing/Closed".
  
 =====   ===== =====   =====
Line 1008: Line 1009:
       - Note: ADDAB now works for astigmatism and coma terms.       - Note: ADDAB now works for astigmatism and coma terms.
  
-===== The Next Slew - Avoid Limit Switch Issues Near AZ : =====+===== The Next Slew - Avoid Triggering AZ Limit Switches: =====
  
 Always pay attention to the AZ you are slewing from or to, to avoid passing the sensors incorrectly and dealing with scopes getting stuck near 90° or 270°. Always pay attention to the AZ you are slewing from or to, to avoid passing the sensors incorrectly and dealing with scopes getting stuck near 90° or 270°.
 +
 +__Az Limit Switch Near 0º:__
  
 There are two sensors negative and positive near AZ 0. There are two sensors negative and positive near AZ 0.
Line 1025: Line 1028:
         * now you can slew back the other way to the next target.         * now you can slew back the other way to the next target.
  
-If you don't pay attention and only hit one sensor at AZ 0, some or all telescopes will continue to stall near 90 or 270 degrees and it is a pain to fix.+If you don't pay attention and only hit one sensor at AZ 0, some or all telescopes will continue to stall near 90 or 270 degrees and it is a pain to fix. Will have to trip the limit switch at the telescope. 
 + 
 +__TCS Az limit beyond -90 and 450º: __ 
 + 
 +On the telescope server, keep an eye on the TCS az to not go beyond -90º and 450º. If you are getting close, telescopes will have to go the other way around to avoid hitting the limit. 
 + 
 +  * can send to STOW or to another star using FIND* on obsgtk.
  
 Got to [[:chara:trouble_shooting#the_telescope_won_t_move_or_stopped_moving|Troubleshooting]], "Azimuth Limit Switches" Section Got to [[:chara:trouble_shooting#the_telescope_won_t_move_or_stopped_moving|Troubleshooting]], "Azimuth Limit Switches" Section
 +
  
 ===== Additional Observing Procedures ===== ===== Additional Observing Procedures =====
Line 1160: Line 1170:
       - Turn off WFS COOL when Matt requests it.       - Turn off WFS COOL when Matt requests it.
       - Never do camerlink off       - Never do camerlink off
-  - Obsgtk, MAIN→ RED OFF, USBOFF, Labao STOP OFF+  - Obsgtk, MAIN→ Labao STOP OFF
   - Shutdown STST   - Shutdown STST
-      - Click the “Start Camera” button to turn off the camera (the button will go from green to gray).+      - Click the “Start Camera” and "Start RTD" button to turn off the camera (the button will go from green to gray).
       - Change the filter wheel to the closed position.       - Change the filter wheel to the closed position.
       - Using the shutter gtk, remove the STST stage from the beams.       - Using the shutter gtk, remove the STST stage from the beams.
Line 1189: Line 1199:
   - Visually check all telescopes in the spycams to make sure all covers and slits are closed. Turn the TV OFF.   - Visually check all telescopes in the spycams to make sure all covers and slits are closed. Turn the TV OFF.
   - Leave GPS, Metrol, and Vacmon servers and the Telescope servers open and running   - Leave GPS, Metrol, and Vacmon servers and the Telescope servers open and running
 +
  
 ==== Manually stowing the telescopes ==== ==== Manually stowing the telescopes ====
chara/new_operating_procedures.1723073957.txt.gz · Last modified: 2024/08/07 19:39 by bflores