This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision | ||
chara:trouble_shooting [2023/07/27 20:10] gail_stargazer |
chara:trouble_shooting [2024/07/22 18:15] (current) gail_stargazer |
||
---|---|---|---|
Line 28: | Line 28: | ||
* Check the instrument alignment. Is flux getting through to the detector? How long has it been since the last NIRO camera alignment? Classic and CLIMB programs can run for about an hour before the light will drift from the central pixel. Use the Classic or CLIMB gui to view the light on the pixels by clicking the PICTURE tab and then the PIXEL AREA button. Turn the camera off with the STOP button. Is the right dither power turned on? CLIMB 1 and Classic use different dithers. If Classic or CLIMB fringes are found in a scan, but not when in recording mode, the dither powers are likely not on. Are the camera settings correct for the seeing conditions and flux levels? | * Check the instrument alignment. Is flux getting through to the detector? How long has it been since the last NIRO camera alignment? Classic and CLIMB programs can run for about an hour before the light will drift from the central pixel. Use the Classic or CLIMB gui to view the light on the pixels by clicking the PICTURE tab and then the PIXEL AREA button. Turn the camera off with the STOP button. Is the right dither power turned on? CLIMB 1 and Classic use different dithers. If Classic or CLIMB fringes are found in a scan, but not when in recording mode, the dither powers are likely not on. Are the camera settings correct for the seeing conditions and flux levels? | ||
* There is a script that will display offsets for all scopes against Hour Angle to help find offsets when using MIRCX and MYSTIC. You'll need to log into the MIRCX spooler computer with the command ssh spooler@mircx, | * There is a script that will display offsets for all scopes against Hour Angle to help find offsets when using MIRCX and MYSTIC. You'll need to log into the MIRCX spooler computer with the command ssh spooler@mircx, | ||
+ | |||
+ | ===== Can't find the star ===== | ||
+ | |||
+ | Sometimes the star does not appear on the ACQ camera and there are many reasons why this can happen. Here are some of those reasons. | ||
+ | |||
+ | * Did the telescope actually slew? If the powers are off or the scope is disabled, it will not slew. | ||
+ | * Did the telescope disable after slewing? Check the dome gui to see if it says it has disabled. Enable to get it going again. | ||
+ | * Are the M1 and M3 covers open? Check with the Telescope monitor or spycam 2 to see if the covers opened. | ||
+ | * Did the dome rotate with the scope? Check with Spycam 1 to see if it is blocking the telescope. Use Autodome On to get it in line with the telescope. | ||
+ | * Is the ACQ camera showing a live view. Hit ACQ or reopen to see a live view. If the server has quit, bootlaunch on the appropriate computer to restart the ACQ server. Sockman will tell which computer the server runs on. Should be wfs computer at each scope. | ||
+ | * Is the ACQ exposure appropriate for the star magnitude? Turn it up as needed to show the star. | ||
+ | * Has the default flat or last flat been loaded after a slew? A bad DM will distort dim stars and they will not be visible. | ||
+ | * Is the star too low or obstructed by a tree or dome? W1 and S2 have trees nearby that can obscure the star below 40 degrees. Refer to the horizon maps to see if they are the cause. | ||
+ | * E1 does not track past 218 degrees azimuth. The finder camera may be needed to find the star again. It will be off in azimuth, but should still show in the finder. | ||
+ | * If a telescope is lost and star does not appear in the finder either, such as after a dome server crash and restart, a bright star, the moon or Jupiter can be used to get the scope pointing correctly. Anything brighter than Vmag 1 will show on the Spycam 1 view and can be used to get the scope close enough to find it in the finder, then ACQ. It should be placed just below the top bar of the telescope, centered left to right using the telescope paddle. You may have to pan up and down to see it move through the finder view. Use the obsgtk ADJUST tab scope paddle and set a step of 3000 and go up and down after centering it in the SPY 1 view below the top telescope bar. When you get it centered in the finder, manually init the scope to the AZ and EL on the MANUAL tab of the dome gui to one decimal place. Use Stellarium online or any resource to get the current position. You should then be able to slew to a star and center it in the finder, then ACQ and init on the obsgtk to get the scope back to usual. | ||
===== The new OPLE system ===== | ===== The new OPLE system ===== | ||
Line 192: | Line 207: | ||
{{: | {{: | ||
- | ==== S2 Acquisition Server | + | ==== Acquisition Server |
- | S2's acquisition server resides on " | + | Most ACQ servers run on the wfs computer at the scope. 2 scopes do not. |
+ | |||
+ | S2's acquisition server resides on " | ||
+ | |||
+ | E1 ACQ and Finder both live on the e1zwo rasperry pi computer. Use ssh e1zwo to log in and run bootlaunch_master to find its PID and kill it and bootlaunch_master again to start it. | ||
==== Focusing the Telescope ==== | ==== Focusing the Telescope ==== | ||
Line 246: | Line 265: | ||
==== LabAO Shutters Not Working ==== | ==== LabAO Shutters Not Working ==== | ||
- | If the labao shutters are not working, the power button on each of the two red control boxes on the top of the table might need to be pressed. After that the other button needs to be pressed and held for 5 seconds so that the units can be controlled remotely. (Note: look for instructions on table.) | + | <font 10.5pt font-family:/ |
+ | |||
+ | <font 10.5pt font-family:/ | ||
+ | |||
+ | <font 10.5pt font-family:/ | ||
==== LabAO DM Electronics ==== | ==== LabAO DM Electronics ==== | ||
Line 464: | Line 487: | ||
Follow instructions in the [[: | Follow instructions in the [[: | ||
+ | |||
+ | ==== No Power for Aperture Wheels ==== | ||
+ | |||
+ | To minimize heat sources in the lab, the power for the apwheels is turned off. If you need to use aperture wheels during the night, the operator will need to plug the power into the outlet next to the metrology table (see photo below). If there are any communication issues after plugging in the power, try restarting the server using bootlaunch on ctrscrut. It's probably a good idea to home the apwheels after turning on the power. | ||
+ | |||
+ | {{: | ||
+ | |||
+ | ==== Restarting the STST Computer ==== | ||
+ | |||
+ | {{: | ||
\\ | \\ | ||
- | Last updated | + | Last updated |