The CHARA Array Wiki

User Tools

Site Tools

Trace:
chara:operating_procedures

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision Both sides next revision
chara:operating_procedures [2021/11/04 17:15]
charaobs 		chara:operating_procedures [2021/11/04 18:20]
charaobs
Line 172: Line 172:
 Once all 6 are solid yellow, right click on each yellow dot, and select start. This loads the control software and will turn the button green. Once all 6 are green, you are ready to start the OPLE server. Once all 6 are solid yellow, right click on each yellow dot, and select start. This loads the control software and will turn the button green. Once all 6 are green, you are ready to start the OPLE server.
  
-If using the CHAPMtoMet feature, once the OPLE server has fully started, please check sockman for CHAMPtoMet. If it is running, then MIRC is ok to start. If it is not running, log into the ople computer and run the command : CHAMPtoMet This is case sensitive.+If using the CHAPMtoMet feature, once the OPLE server has fully started, please check sockman for CHAMPtoMet. If it is running, then MIRC is ok to start. If it is not running, log into the ople computer and run the command : CHAMPtoMet This is case sensitive.  This is not the usual mode of controlling the carts.
  
 Now the MIRC server is ok to start. Be sure to inform the MIRCX/MYSTIC PI that you are done in the lab and that it is ok to start any alignments or STS recording that is desired. Now the MIRC server is ok to start. Be sure to inform the MIRCX/MYSTIC PI that you are done in the lab and that it is ok to start any alignments or STS recording that is desired.
Line 214: Line 214:
  
 <font 14px/Arial,Helvetica,sans-serif;;#333333;;white>After the carts finish homing, the ople server will say “HOMESETDONE” * To check that the carts have homed properly, click [TRACK] on the Control Tab of the OPLE</font>   GUI<font inherit/inherit;;initial;;inherit>* The cart will track to home switch at the target position of “0.000000” on the OPLE Server * Make sure the “X” lights up and stays steady under the HM column on the Primary OPLE Server for each cart you will be using. Also make sure that the errors between the laser and target position are small, (0.007µm or less is typical), when tracking at the home switch. If the errors jump when the cart is tracking on the home switch, then turn the cart [OFF], move the cart [BACK] about a meter from the home switch, turn the cart [OFF], and try clicking [TRACK] again. Please wait for each command to register on the OPLE server before clicking the next button in this sequence. If the errors do not stay near zero, the metrology laser may be out of alignment and the signal is low. Pull up a metrology signal window as shown above and confirm the signal is strong. It will look like a sine wave with an amplitude the same as the window height. If it is low, adjust it carefully with the MET2 gui in PICO 2. Get the sine wave to equal the window height. If it is ok and the problem persists, you can try to restart the respective cart’s computer/OPLE1-6 server(s). Try tracking the cart again. After checking to make sure the carts track properly, turn the carts [OFF]</font>. <font 14px/Arial,Helvetica,sans-serif;;#333333;;white>After the carts finish homing, the ople server will say “HOMESETDONE” * To check that the carts have homed properly, click [TRACK] on the Control Tab of the OPLE</font>   GUI<font inherit/inherit;;initial;;inherit>* The cart will track to home switch at the target position of “0.000000” on the OPLE Server * Make sure the “X” lights up and stays steady under the HM column on the Primary OPLE Server for each cart you will be using. Also make sure that the errors between the laser and target position are small, (0.007µm or less is typical), when tracking at the home switch. If the errors jump when the cart is tracking on the home switch, then turn the cart [OFF], move the cart [BACK] about a meter from the home switch, turn the cart [OFF], and try clicking [TRACK] again. Please wait for each command to register on the OPLE server before clicking the next button in this sequence. If the errors do not stay near zero, the metrology laser may be out of alignment and the signal is low. Pull up a metrology signal window as shown above and confirm the signal is strong. It will look like a sine wave with an amplitude the same as the window height. If it is low, adjust it carefully with the MET2 gui in PICO 2. Get the sine wave to equal the window height. If it is ok and the problem persists, you can try to restart the respective cart’s computer/OPLE1-6 server(s). Try tracking the cart again. After checking to make sure the carts track properly, turn the carts [OFF]</font>.
 +
 +The new ople system has a home check procedure that will give the homing error of each cart.  In the ople server, use the command homechk S1, S2,... to have ople check the homing accuracy.  A value of a few microns is usually returned after the cart is checked.  Hit ESC to clear the display and enter the next cart.  If any cart has large values above 20 microns, home the cart again and check the homing until it shows low values.
  
 3.8 Synchronizing the clocks 3.8 Synchronizing the clocks
Line 257: Line 259:
 4.6 Essential Observing Links 4.6 Essential Observing Links
  
-150-Foot Solar Tower Current TowerCam Image ([[http://www.astro.ucla.edu/%7Eobs/towercam.htm|http://www.astro.ucla.edu/~obs/towercam.htm]]) a live view of the mountain. Check the clock when viewing the page as it can sometimes fail to refresh.+Mount Wilson HP Wren Cameras ([[http://hpwren.ucsd.edu/cameras/wilson.html|http://hpwren.ucsd.edu/cameras/wilson.html]]) 360º view of mountain in color and IR
  
 Caltech Millikan Library Camera ([[http://library.caltech.edu/milcam/|http://library.caltech.edu/milcam/]]) A view of Mt. Wilson from the south, good for watching low clouds and fog that cling to the mountain. Caltech Millikan Library Camera ([[http://library.caltech.edu/milcam/|http://library.caltech.edu/milcam/]]) A view of Mt. Wilson from the south, good for watching low clouds and fog that cling to the mountain.
Line 263: Line 265:
 National Weather Service ([[http://forecast.weather.gov/MapClick.php?site=lox&textField1=34.2231&textField2=-118.0587&smap=1#.VKsuq2TF8rO|http://forecast.weather.gov]]) Mount Wilson weather and 5 day forecast National Weather Service ([[http://forecast.weather.gov/MapClick.php?site=lox&textField1=34.2231&textField2=-118.0587&smap=1#.VKsuq2TF8rO|http://forecast.weather.gov]]) Mount Wilson weather and 5 day forecast
  
-CHARA telescopes spy cams and weather graph ([[http://astro.gsu.edu/~weather/chara_scopes.html|http://www.astro.gsu.edu]]) Status of each CHARA telescope and the All-sky camera.+Mount Wilson Ambient station [[https://ambientweather.net/dashboard/c68efe875521e576a9694913bdd92e65|https://ambientweather.net/dashboard/c68efe875521e576a9694913bdd92e65]]
  
-Mount Wilson HP Wren Cameras ([[http://hpwren.ucsd.edu/cameras/wilson.html|http://hpwren.ucsd.edu/cameras/wilson.html]]) 360º view of mountain in color and IR +Jet stream forecast [[https://weatherstreet.com/models/gfs-jetstream-wind-forecast.php|https://weatherstreet.com/models/gfs-jetstream-wind-forecast.php]] Monitors high level winds which degrade seeing
- +
-Aerospace Corporation weather station ([[http://www.weatherlink.com/user/mocam/index.php?view=summary&headers=1|http://www.weatherlink.com/user/mocam]]) Another local station, always current. +
- +
-Jet stream forecast ([[http://squall.sfsu.edu/scripts/jetstream_modelsml_fcst.html|http://squall.sfsu.edu/scripts/jetstream_modelsml_fcst.html]]) Monitors high level winds which degrade seeing+
  
 IR satellite loop ([[http://www.wrh.noaa.gov/lox/scripts/animate.php?root=sat_4km&list=IR4.GIF.3.jpg,IR4.GIF.4.jpg,IR4.GIF.5.jpg,IR4.GIF.6.jpg,IR4.GIF.7.jpg,IR4.GIF.8.jpg|http://www.wrh.noaa.gov]]) Keeps an eye on storms and clouds coming in IR satellite loop ([[http://www.wrh.noaa.gov/lox/scripts/animate.php?root=sat_4km&list=IR4.GIF.3.jpg,IR4.GIF.4.jpg,IR4.GIF.5.jpg,IR4.GIF.6.jpg,IR4.GIF.7.jpg,IR4.GIF.8.jpg|http://www.wrh.noaa.gov]]) Keeps an eye on storms and clouds coming in
Line 276: Line 274:
  
 Clear Sky Clock ([[http://cleardarksky.com/c/MtWilsonOBCAkey.html|http://cleardarksky.com/c/MtWilsonOBCAkey.html]]) a forecasting tool, but be aware that the humidity forecast is often incorrect on this site as it incorporates the marine layer forecast for the valley below, which does not affect us 80-90% of the time Clear Sky Clock ([[http://cleardarksky.com/c/MtWilsonOBCAkey.html|http://cleardarksky.com/c/MtWilsonOBCAkey.html]]) a forecasting tool, but be aware that the humidity forecast is often incorrect on this site as it incorporates the marine layer forecast for the valley below, which does not affect us 80-90% of the time
 +
 +CHARA telescopes spy cams and weather graph ([[http://astro.gsu.edu/~weather/chara_scopes.html|http://www.astro.gsu.edu]]) Not updating.
  
 \\ \\
chara/operating_procedures.txt · Last modified: 2023/09/01 02:50 by gail_stargazer

Page Tools

Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
CC Attribution-Share Alike 4.0 International Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki