This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
chara:trouble_shooting [2022/02/10 13:38] charaobs |
chara:trouble_shooting [2022/12/09 20:07] gail_stargazer |
||
---|---|---|---|
Line 18: | Line 18: | ||
* Check the time on the OPLE server. If the time is off or there are any lost ticks/ | * Check the time on the OPLE server. If the time is off or there are any lost ticks/ | ||
* Are the [MAN] buttons pressed (gray) for the moving carts on the OPLE Control gui? (The reference cart will remain green.) | * Are the [MAN] buttons pressed (gray) for the moving carts on the OPLE Control gui? (The reference cart will remain green.) | ||
- | * Check that the carts are within delay line range (-1.3 to 44.25 meters) and errors are small. Were the carts homed and checked before the first slew of the night? Did any carts go to the front switch after slewing? This can cause them to lose their position. | + | * Check that the carts are within delay line range (-1.3 to 44.25 meters) and errors are small. Were the carts homed and checked before the first slew of the night? Did any carts go to the front switch after slewing? This can cause them to lose their position. |
* Are the LDC's working? | * Are the LDC's working? | ||
* Is the glass position within allowable range (-10mm to 49mm) on all beams? | * Is the glass position within allowable range (-10mm to 49mm) on all beams? | ||
Line 26: | Line 26: | ||
* Check the instrument alignment. Is flux getting through to the detector? How long has it been since the last NIRO camera alignment? Classic and CLIMB programs can run for about an hour before the light will drift from the central pixel. Use the Classic or CLIMB gui to view the light on the pixels by clicking the PICTURE tab and then the PIXEL AREA button. Turn the camera off with the STOP button. Is the right dither power turned on? CLIMB 1 and Classic use different dithers. If Classic or CLIMB fringes are found in a scan, but not when in recording mode, the dither powers are likely not on. Are the camera settings correct for the seeing conditions and flux levels? | * Check the instrument alignment. Is flux getting through to the detector? How long has it been since the last NIRO camera alignment? Classic and CLIMB programs can run for about an hour before the light will drift from the central pixel. Use the Classic or CLIMB gui to view the light on the pixels by clicking the PICTURE tab and then the PIXEL AREA button. Turn the camera off with the STOP button. Is the right dither power turned on? CLIMB 1 and Classic use different dithers. If Classic or CLIMB fringes are found in a scan, but not when in recording mode, the dither powers are likely not on. Are the camera settings correct for the seeing conditions and flux levels? | ||
- | * There is a script that will display offsets for all scopes against Hour Angle to help find offsets when using MIRCX and MYSTIC. | + | * There is a script that will display offsets for all scopes against Hour Angle to help find offsets when using MIRCX and MYSTIC. You'll need to log into the MIRCX spooler computer with the command ssh spooler@mircx, |
===== The new OPLE system ===== | ===== The new OPLE system ===== | ||
Line 55: | Line 55: | ||
\\ The Shutters server can become unresponsive or disconnected from the Socket Manager. This server must be restarted from the lab and not from the Control Room. Follow these instructions to restart it. Note that Shutters runs on ople, not ctrscrut. \\ \\ To start the shutter server on ople: \\ \\ Log into the ople computer and kill the process labeled shutters with the PID as described in **Restarting Servers** | \\ The Shutters server can become unresponsive or disconnected from the Socket Manager. This server must be restarted from the lab and not from the Control Room. Follow these instructions to restart it. Note that Shutters runs on ople, not ctrscrut. \\ \\ To start the shutter server on ople: \\ \\ Log into the ople computer and kill the process labeled shutters with the PID as described in **Restarting Servers** | ||
+ | |||
+ | ==== Restarting Socket Manager ==== | ||
+ | |||
+ | In very rare circumstances, | ||
+ | |||
+ | Follow these instructions to restart the socket manager, but only do so if really necessary: | ||
+ | |||
+ | ssh -X observe@ctrscrut | ||
+ | |||
+ | killall socket_manager | ||
+ | |||
+ | socket_manager & | ||
==== MIRC-X CredoneImAcq Server ==== | ==== MIRC-X CredoneImAcq Server ==== | ||
Line 286: | Line 298: | ||
* If either Phase 1 or Phase 2 states say IDLE for a given VPN, then you need to re-establish the connection. To do this, click on the " | * If either Phase 1 or Phase 2 states say IDLE for a given VPN, then you need to re-establish the connection. To do this, click on the " | ||
* Make sure to close Firefox by using CTRL-Q to quit the program and not just close the window. | * Make sure to close Firefox by using CTRL-Q to quit the program and not just close the window. | ||
+ | |||
+ | ===== Network Problems ===== | ||
+ | |||
+ | ==== User accounts not recognized ==== | ||
+ | |||
+ | The gps computer does the user authentication for the control side while ctrscrut provides the home directories. Yellowpages is gone, the new paradigm is LDAP (local directory access protocol). If you can't log on to computers on the control network, then make sure both ctscrut (michelson) and gps computers are running. If the login screen screen on ctrscrut says " | ||
+ | |||
+ | If gps computer does not start, check the power distribution unit (PDU) at the top of that rack. If any units show both " | ||
===== General Problems ===== | ===== General Problems ===== |