The CHARA Array Wiki

User Tools

Site Tools

Trace: • cophasing_with_the_new_chancam • labao_alignment_procedure
chara:new_operating_procedures

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
Next revision Both sides next revision
chara:new_operating_procedures [2024/04/17 07:29]
bflores [Starting the vacuum pump and opening valves] 		chara:new_operating_procedures [2024/04/30 00:04]
bflores [Common Issues]
Line 1: Line 1:
 ====== New Operating Procedures ====== ====== New Operating Procedures ======
  
-Last updated 04/17/2024+Last updated 04/22/2024
  
 [[:chara:operating_procedures|Link for Old Operating Procedures Page]] [[:chara:operating_procedures|Link for Old Operating Procedures Page]]
Line 818: Line 818:
         - can use rotation wheel. spica is 90 degrees CW from azimuth of star.         - can use rotation wheel. spica is 90 degrees CW from azimuth of star.
         - use steps 222 - 500 and wait for dm to adjust before clicking again.         - use steps 222 - 500 and wait for dm to adjust before clicking again.
-      - as of 10/13, spica requests that telemetry is recorded once data sequence is being recorded. +      - when finished, on ip_det, press **[FTT SERVO] **and** [OFFLOAD]**.
-        - **CD,**  Control tab, next to Star Acquired, **[TELEMETRY]**  (click once, nothing will pop up)+
   - Make sure data acquired line comes in on CD, otherwise do **[DATA ACQ]. **   - Make sure data acquired line comes in on CD, otherwise do **[DATA ACQ]. **
       - or make sure to **[REOPEN]**  CD during shutters       - or make sure to **[REOPEN]**  CD during shutters
Line 1278: Line 1277:
         - if that doesn't work, go to the lab and try giving it a soft nudge to get it unstuck.         - if that doesn't work, go to the lab and try giving it a soft nudge to get it unstuck.
         - if it doesn't move, check that the ribbon and cable are on the track and not caught somewhere. Also check the cable spooler is not loose and wind it up if it is.         - if it doesn't move, check that the ribbon and cable are on the track and not caught somewhere. Also check the cable spooler is not loose and wind it up if it is.
-  - cart error is jumping about 100 microns every 4-6 seconds. +  - cart error is jumping about 100 microns every 4-6 seconds. On mircx/mystic, fringes will show an oscillating pattern that corresponds to the jump in cart error. In the lab, a faint ticking sound may also be heard. 
-      - On mircx/mystic, fringes will show an oscillating pattern that corresponds to the jump in cart error. +      - First try restarting ople server. 
-      - In the lab, a faint ticking sound could also be heard. +        - Turn off the carts 
-      - Turn off the cart +        - Restart ople server 
-      - On Ople System Controller, restart the ople computer for the cart +        - Track carts. 
-      - When its done, rehome and check the cart. Issue should go away.+      - if problem persists, restart ople system controller. 
 +        - On Ople System Controller, restart the ople computer for the cart. 
 +        - When its done, rehome and check the cart. Issue should go away.
  
 === Hut Error === === Hut Error ===
chara/new_operating_procedures.txt · Last modified: 2024/05/15 06:00 by bflores

Page Tools

Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Share Alike 4.0 International
CC Attribution-Share Alike 4.0 International Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki